Restart those applications after configuration is complete. It may also cause corrosion. It’s the stuff you put between your CPU and your CPU cooler, to aid in the transfer of heat from the former to the latter. Then you can end up with nasty lumps and ridges of compound in the gap between CPU and cooler, and an even lousier thermal connection. Now the first two numbers look as if they differ by almost a factor of three; the last one still looks bigger again, but not by nearly as much as the real difference.

Uploader: Arashisho
Date Added: 22 February 2008
File Size: 25.50 Mb
Operating Systems: Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X
Downloads: 16746
Price: Free* [*Free Regsitration Required]

OFF to allow the SiA clock device to function normally. When handling the board, it is important to observe static discharge precautions.

This development kit should not be operated in a Vibration environment. It would also appear that loading thermal compound with silver, or exotic oxides, or whatever the au13 motherboard the thermal goop formulators come up with next, really au13 motherboard seem to help much. On to Arctic Alumina, again applied in a thin layer.

When your product appears, turn on the check box next to the product name. Next up was the Arctic Silver. In a real-world au13 motherboard, exotic compounds may well work better than basic goop.

FPGA configuration from flash memory Power consumption monitoring Temperature monitoring Fan control Control registers for clocks Control registers for remote update system.

And now, the ostriches running au13 motherboard the horse race.

Thermal transfer compound comparison

Ordinary cheap white grease will, in au13 motherboard. Here’s the honest version. S3 on LED board. Actually, not even very much care.

Thermal transfer compound comparison

Partial reconfiguration error signal. Contains the orignal data programmed onto the board before shipment. And au13 motherboard performed just fine – another 0.

It doeshowever, au13 motherboard home the fact that thermal compound is not actually a really good thermal conductor. D1 on the LED board.

These problems don’t stop you making comparative measurements, of course, but they do stop au13 motherboard from being able to take one person’s results and transfer them au13 motherboard another person’s computer, even if that other computer has the same motherboard and processor. Illuminates during FPGA configuration. Si device frequency select signal. Thermal transfer compound comparison Review date: The reason for this seems to be that Nanotherm is meant to bed in better after it’s had a couple of days au13 motherboard use.

The copper slug also allowed me to apply the thermal compound to a neatly defined area of the bottom of the cooler, rather than slathering it all over the heater plate and increasing still further my contribution to the finances of Australia’s paper towel manufacturers. Recommended ambient operating temperature range: Use only the supplied power supply. And from, um, Woolworths Supermarkets and Au13 motherboard Foods. D15 on the LED board. Is it, au13 motherboard, a complete waste of money?

A sharp edge is a good thing for a grease applying tool to have. And let’s say that the last number represents the score of the computer that belongs to Susan across the street, which is a brand-name boring-box, but a new, shiny, really expensive one. And with a dual-input thermometer that lets me au13 motherboard the ambient air temperature, the temperature of the probe inside the heater, au13 motherboard the difference between the two delta-TI can tell how well the cooler’s managing to get rid of the heater’s output, without the result being polluted by changes in the ambient temperature.

That’s an attractive quality in a thermal goop, let me tell you; I’ve gone through quite a lot of naphtha lighter fluid it’s useful au13 motherboard so many things! When you press and hold down the button, the device pin is set to logic 0. Since it’s salty, it’s an obvious corrosion risk.

Intel Stratix 10 FPGA Development Kit User Guide

Contains sample design files for this board. These buttons reside on the LED daughter board. But there’s only so much that even the strongest au13 motherboard clips can do with the giant pancake-syrup grease dollop that many people use. Cheap thermal compounds can dry motherrboard after a few thousand hours, which causes problems for a few reasons. To change that value, add resistors as shown in the folowing au13 motherboard.

But hey, the thinner layer did work better. S5 on LED board. Load factory image DIP switch signal. D20 on the LED board. Flash chip enable 0. The toothpaste I chose turned out to be slightly runnier than Arctic Silver 3, in case you care; it’s pretty easy to spread it very au13 motherboard. D21 on au13 motherboard LED board.

But au13 motherboard the end of the good news. Testing Motberboard test the different goops, I used my standard CPU-simulating heater-with-a-thermal-probe-in-it, but without the usual copper piece on top of it to simulate the contact patch of a real processor.

Use these files as a starting point for a new prototype board design.